Method for manufacturing of an aluminum-magnesium-lithium product, comprising the steps of subsequently: (a) providing an aluminum alloy consisting of (in weight %): Mg 3.0-6.0, Li 0.4-3.0, Zn up to 2.0, Mn up to 1.0, Ag up to 0.5, Fe up to 0.3, Si to 0.3, Cu up to 0.3, 0.02-0.5 selected from the group consisting of (Sc 0.010-0.40, Hf 0.010-0.25, Ti 0.010-0.25, V 0.010-0.30, Nd 0.010-0.20, Zr 0.020-0.25, Cr 0.020-0.25, Y 0.005-0.20, Be 0.0002-0.10), balance consisting essentially of aluminum and incidental elements and impurities; (b) casting the aluminum alloy into an ingot; (c) preheating the ingot; (d) hot rolling the preheated ingot to a hot worked intermediate product; (e) cold rolling the hot worked intermediate product to a rolled product in both the length and in the width direction with a total cold rolling reduction of at least 15%; (f) solution heat treating the cold rolled product in the temperature range of 465 to 565.degree. C. for a soaking time in the range of 0.15 to 8 hours; (g) cooling the solution heat treated product from the solution heat treatment temperature to below 150.degree. C. with a cooling rate of at least 0.2.degree. C./sec; (h) ageing the cooled product to provide a sheet or thin plate product having a minimum yield strength of 260 MPa or more and a minimum tensile strength of 400 MPa or more in at least the L- and LT-direction, a minimum yield strength of 230 MPa or more and a minimum tensile strength of 380 MPa or more in the 45.degree. to the L-direction, and further having a minimum T-L fracture toughness K.sub.CO of 80 MPa. or more for 400 mm wide CCT-panels.

Método para la fabricación de un producto del aluminio-magnesio-litio, abarcando los pasos de posteriormente: (a) abastecimiento de una aleación de aluminio que consiste en (en el peso %): magnesio 3.0-6.0, li 0.4-3.0, zn hasta 2.0, manganeso hasta 1.0, AG hasta 0.5, FE hasta 0.3, silicio a 0.3, Cu hasta 0.3, 0.02-0.5 seleccionado del grupo que consiste en (el Sc 0.010-0.40, Hf 0.010-0.25, ti 0.010-0.25, V 0.010-0.30, Nd 0.010-0.20, zr 0.020-0.25, cr 0.020-0.25, Y 0.005-0.20, sea 0.0002-0.10), balance que consiste esencialmente en los elementos y las impurezas de aluminio y fortuitos; (b) echar la aleación de aluminio en un lingote; (c) precalentar el lingote; (d) balanceo caliente el lingote precalentado a un producto intermedio trabajado caliente; (e) frío que rueda el producto intermedio trabajado caliente a un producto laminado en la longitud y en la dirección de la anchura con una reducción fría total del balanceo de por lo menos el 15%; (f) calor de la solución que trata el producto laminado en frío en la gama de temperaturas de 465 a 565.degree. C. por un tiempo que empapa en el radio de acción de 0.15 a 8 horas; (g) refrescar el producto tratado calor de la solución de la temperatura del tratamiento de calor de la solución debajo de 150.degree. C. con un índice que se refresca por lo menos de 0.2.degree. C./sec; (h) envejeciendo el producto refrescado para proporcionar una hoja o un producto fino de la placa que tiene una fuerza de la producción mínima de 260 MPa o más y una fuerza extensible mínima de 400 MPa o más en por lo menos el l y la Teniente-direccio'n, una fuerza de la producción mínima de 230 MPa o más y una fuerza extensible mínima de 380 MPa o más en el 45.degree. a la L-direccio'n, y fomente tener una dureza K.sub.CO de la fractura del T-L del mínimo de 80 MPa. o más para 400 milímetros CCT-panels ancho.

 
Web www.patentalert.com

< Process for manufacturing a strip made of an Fe-Ni alloy

< Method for manufacturing cold-rolled steel sheet

> Steel wire and method of manufacturing the same

> Process to improve 6XXX alloys by reducing altered density sites

~ 00068